Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.

SMTnet
»
Electronics Forum
»
MCS30 Problem

MCS30 Problem

Subscribe to Thread

Hi all, Please help me to solve this problem: When I tur... - Aug 31, 2007 by duyhoang

Hi- If it turns out your MCS-30 has died, I have a few co... - Aug 31, 2007 by Fastek

I would go into the system BIOS and see if everything looks ... - Aug 31, 2007 by Chris

Yea, boot device fail is just the hard drive dead most likel... - Sep 04, 2007 by jdumont

What are the status of the LEDs? Are these LEDs lighted up i... - Sep 05, 2007 by jepoy

Dear jepoy, I did as you directed but MCS couldn't recogniz... - Sep 05, 2007 by duyhoang

We had a simliar problem with our MCS30, we ended up replaci... - Sep 06, 2007 by Murray Northey

We're running 3 CP3's but I think they doesn't meet Flexa. F... - Sep 06, 2007 by duyhoang

After you tried the procedure, what the MCS error indicate? ... - Sep 09, 2007 by jepoy

duyhoang

#51616

MCS30 Problem | 31 August, 2007

Hi all,

Please help me to solve this problem: When I turn on MCS30, it couldn't boot. It appears this error: " BOOT DEVICE ALL FAIL !". Please help me ASAP.

Thanks,

reply »

Fastek

#51619

MCS30 Problem | 31 August, 2007

Hi-

If it turns out your MCS-30 has died, I have a few complete and running units in stock to replace it.

Rick

MCS30 Problem | 31 August, 2007

I would go into the system BIOS and see if everything looks good. Check out the boot sequence and make sure it recognizes the hard drive. If that is good you probably have a bad drive. It is a good idea to make a copy of your drive's in case of crashes.

reply »

jdumont

#51643

MCS30 Problem | 4 September, 2007

Yea, boot device fail is just the hard drive dead most likely. Its looking for the system files and cannot find them. You can prob buy a replacement hard drive with the necessary files on it from the supplier if you have no backup...

reply »

jepoy

#51652

MCS30 Problem | 5 September, 2007

What are the status of the LEDs? Are these LEDs lighted up in RED? If so, the harddrive and the sub are disabled. You can enable these if you have the system disc. Insert the system disc, then, $ sign will appear. Type hdstat. This will display the status of the harddrive. To enable the drives, type hadstat = +main then enter. This will enable the harddrive. For the sub, type hdstat = +sub then enter. After this, shutdown the PC. If the PC still unable to boot. Try to re-format and install all the recovery disc.

reply »

duyhoang

#51673

MCS30 Problem | 5 September, 2007

Dear jepoy, I did as you directed but MCS couldn't recognize the main and sub HDD. It appeared that : ERROR! I don't know what to do? What's wrong with my MCS? What should I do now to solve this problem. You have much experience in MCS, I hope you'll help me and that would be my great thankfulness for you. I highly appreciate your assistance. Regards,

reply »

Murray Northey

#51685

MCS30 Problem | 6 September, 2007

We had a simliar problem with our MCS30, we ended up replacing the MCS30 with FLEXA from Fuji. the program was expensive but we used an off the shelf computer, (cheap). We are running 6 CP3's with the one computer at about ten times the speed. Very user friendly once programs are installed. A FUJI Rep. came in and helped with the setup.

Good Luck Murray

reply »

duyhoang

#51690

MCS30 Problem | 6 September, 2007

We're running 3 CP3's but I think they doesn't meet Flexa. Flexa is only connected when CP3 has Version more than 6.9 . We only have ver.1.4 and 6.8. I really don't know what to do now. Anyone helps me?

reply »

jepoy

#51702

MCS30 Problem | 9 September, 2007

After you tried the procedure, what the MCS error indicate? If you try to format the PC, all data stored will be erased.

reply »