Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.

SMTnet
»
Electronics Forum
»
Hi There, How do I adjust table height EKRA X5 Screen Printer? Could you share me the Systems manual Operation? Thanks

Hi There, How do I adjust table height EKRA X5 Screen Printer? Could you share me the Systems manual Operation? Thanks

Subscribe to Thread

Views: 2747

Hi, How to adjust the table height of Screen Printing EKRA X... - Aug 03, 2020 by Bang ir

How much adjustment is needed? Adjusting the snap off will g... - Aug 04, 2020 by Chris

Hi Chris, It's arround +/- 2MM. There was a gap if running p... - Aug 04, 2020 by Bang ir

There are one value for thickness during PCB-teach function ... - Aug 04, 2020 by Kristof_K

So 1MM is the board thickness in your program? ... - Aug 04, 2020 by Chris

Yes if you adjust the thickness to be thin than the machine ... - Aug 05, 2020 by Kristof_K

Hi Cris, Yes, The PCB thickness is 1mm. the PCB position bel... - Aug 05, 2020 by Bang ir

Snap off is an option to make distance between PCB and stenc... - Aug 05, 2020 by Kristof_K

Hi Chris, Thank you for your advise. We got problem on key i... - Aug 06, 2020 by Bang ir

Try 2211. I honestly can't remember what this gets you into.... - Aug 06, 2020 by Chris

9060, service code 3560, engineer code (as I remember) ... - Aug 08, 2020 by Kristof_K

Call +4 (Christian) Ekra screen printer specialist. ... - Aug 13, 2020 by Marks

How do I adjust table height EKRA X5 Screen Printer? | 3 August, 2020

Hi, How to adjust the table height of Screen Printing EKRA X5? Could you share me the Manual System Operation?

How do I adjust table height EKRA X5 Screen Printer? | 4 August, 2020

How much adjustment is needed? Adjusting the snap off will get the PCB tighter/looser to the stencil. But this is only a 3 to -3 MM adjustment.

How do I adjust table height EKRA X5 Screen Printer? | 4 August, 2020

Hi Chris, It's arround +/- 2MM. There was a gap if running pcb with thickness 1MM. The PCB position below the rail table.

How do I adjust table height EKRA X5 Screen Printer? | 4 August, 2020

There are one value for thickness during PCB-teach function which is the PCB thickness.

The other one is the camera focus in machine option but it is a dangerous function because the camera focus is adjusted by raising/lowering table.

How do I adjust table height EKRA X5 Screen Printer? | 4 August, 2020

So 1MM is the board thickness in your program?

How do I adjust table height EKRA X5 Screen Printer? | 5 August, 2020

Yes if you adjust the thickness to be thin than the machine raise the PCB more to the stencil - than the foil have better tension but it string out faster.

How do I adjust table height EKRA X5 Screen Printer? | 5 August, 2020

Hi Cris, Yes, The PCB thickness is 1mm. the PCB position below the rail thickness when the table go up the print position. Please advice or do you the service manual book.

How do I adjust table height EKRA X5 Screen Printer? | 5 August, 2020

Snap off is an option to make distance between PCB and stencil. If the distance not enought, adjust the PCB thickness too. Mostly we don't use snap off, I more prefer if the stencil is tight with the PCB - I know, this make the stencil lifetime worst.

How do I adjust table height EKRA X5 Screen Printer? | 6 August, 2020

Hi Chris, Thank you for your advise. We got problem on key in parameters. Why we can't save value on parameter after key in manually? When we key in Parameter, we used password 9060. Is there any other password to key in and save machine parameter? Thank you

How do I adjust table height EKRA X5 Screen Printer? | 6 August, 2020

Try 2211. I honestly can't remember what this gets you into. But I used it years ago.

How do I adjust table height EKRA X5 Screen Printer? | 8 August, 2020

9060, service code 3560, engineer code (as I remember)

How do I adjust table height EKRA X5 Screen Printer? | 13 August, 2020

Call +4 (Christian) Ekra screen printer specialist.

SMTnet
»
Electronics Forum
»
Hi There, How do I adjust table height EKRA X5 Screen Printer? Could you share me the Systems manual Operation? Thanks

One-stop Platform For All Your Need For SMT - QYSMT

How much time do you spend on production change-over? Learn how to streamline High-Mix Low-Volume operations.

Wave Soldering 101 Training Course

© 1995-2024 SMTnet

SMT Reflow Ovens

Now Online

8
Visitors

0
Member

Who are SMTnet visitors?

Become a member now and receive the value and benefits of membership.

Industry 4.0 Reflow Oven

Online IPC Training & Certification

Fluid Dispense Pump Integration